Thermaltake Pacific G1/4 Pressure Equalizer Stop Plug w/ O-Ring - Black
The Pacific G1/4 Pressure Equalizer Stop Plug fitting is made for helping release excess air or pressure in your
pump. Finished in chrome/black-plated copper, the G1/4 pressure equalizer plug is designed to install on the top
of reservoir, and utilizes leak-free design with a preinstalled O-ring. Enjoy the ultimate in custom PC water
cooling configurations with high quality components from Thermaltake.
Tt LCS Certified
Tt LCS Certified is a Thermaltake exclusive certification applied to only
products that pass the design and hardcore enthusiasts standards that a true LCS chassis should be held to.
The Tt LCS certification was created so that we at Thermaltake can designate to all power users which chassis
have been tested to be best compatible with extreme liquid cooling configurations to ensure you get the best
performance from the best features and fitment.
Leak-free Design
Committed to deliver the highest quality, the fitting includes one
preinstalled O-ring and allows proper connection to G1/4” thread, securing properly to any cooling components.
Available in chrome and black finishes.
Remarkable Expansion
Thermaltake offers a full line of Pacific Series components for enthusiasts
to build up aesthetically-superior water cooling systems by incorporating externally-modular upgrades for
their chassis.
*Note:
1. Please keep the plug away from liquid.
2. Please check the reservoir immediately if the water level is rising.
3. Please maintain the reservoir 80% full when the plug is installed.
Caution
Thermaltake recommends the following steps to be taken before using the
Pacific series radiators and water blocks
- It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.
- Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
- DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately
- Fill the reservoir to the top as it will prevent air from going into the pump
- If necessary tilt the system slightly from side to side to bleed the air out of the loop.
- Place some paper towels under fittings and joining points to test for leaks.
- Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop
- Before starting, flush out your system correctly to prevent any coolant or unwanted particles sticking to your tubes, radiators and other cooling components.
- Coolant might fade over time.
Cautions
Thermaltake recommends the following steps to be taken before using the Pacific series radiators and water blocks:
- To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.
- Do not use tap water or distilled water as your coolant; it may harm your loop and reduce performance.
- It is strongly recommended to use market-proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while protecting the entire liquid loop from corrosion.
- Before storing your water cooling components, please clean, rinse, and dry them to ensure a longer lifespan for your components.
Thermaltake recommends the following steps to be taken after completing your water loop setup:
- It is strongly recommended to use market-proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing corrosion in the entire cooling system – copper, brass, nickel, aluminum, and steel.
- Fill the reservoir with coolant and cycle the power on and off several times while the pump pushes the coolant into the loop.
- DO NOT let the pump run dry; turn off the power immediately if there is no liquid entering the pump.
- Fill the reservoir to the top to prevent air from entering the pump.
- If necessary, tilt the system slightly from side to side to bleed air out of the loop.
- Place some paper towels under fittings and joining points to check for leaks.
- Run the loop with the fill port open for about 24 hours to completely bleed air out of the loop.
- Before starting, flush your system correctly to prevent any coolant or unwanted particles from sticking to your tubes, radiators, and other cooling components.
- Note that coolant might fade over time.
| P/N | CL-W086-CU00BL-A |
|---|---|
| Material | CU |
| Dimensions | ∮18 x 12.9 (H) (mm) |
| Weight | 12 g |
| Applicable | G1/4” |
| Screw Thread | G 1/4 |
User Manual
- File Name
- Description
- Size
- Version
- Release Date
-
Manual
- Multi-language
- 3.6 MB
- 2017-01-12
