Currency
EUR
Search
Advanced Search
My Cart 0
Trustpilot
V-Tubler 3T
V-Tubler 3T

V-Tubler 3T

In stock
P/N
CL-W018-OS00TR-A
€8.90 (included VAT)

The V-Tubler 3T 200cm ID 3/8” (9.5 mm) OD 5/8” (16 mm) flexible tubing for custom PC water cooling configurations.


Thermaltake Flexible Tubing V-Tubler 3T 3/8’’ (9.5 mm)

Thermaltake introduces the V-Tubler 3T water tubing for custom PC water cooling configurations. Manufactured from medical grade PVC material, the V-Tubler resists twisting and collapse allowing for tighter bends without the kinking that can cause cooling failures or a reduction in system performance. Designed for use with 3/8” barbs and compression fittings, give users better mounting, easier fitting, and ideal flow. Choose from: ID 1/2” or 3/8” to make your system a showcase for all to see with the Thermaltake V-Tubler water tubing.

Tt LCS Certified

Tt LCS Certified is a Thermaltake exclusive certification applied only to products that pass the design and hardcore enthusiasts standards that a true LCS chassis should hold to. The Tt LCS certification was created so that we at Thermaltake can indicate to all power users which chassis have been tested to be best compatible with extreme liquid cooling configurations, ensuring you get the best performance from the best features and fitment.

Medical Grade Construction

Made in Taiwan, the V-Tubler 3T is constructed from medical grade PVC which is reliable, non-toxic, and substance free. Smooth inner walls improve closed loop sanitation, reducing particular gathering/entrapment onto the tubing wall. Working temperature range from -4℉ (-20℃) to 140℉ (60℃).
- Inner diameter: 3/8” (9.5 mm)
- Outer diameter: 5/8” (16 mm)
Material of V -Tubler 3T as below:


Remarkable Expansion

Designed for use with 3/8” barbs and compression fittings, V-Tubler 3T is pre cut into retail coils of 200cm lengths, allowing enthusiasts to build up aesthetically-superior water cooling systems by allocating the radiators to each particular component and incorporating externally-modular upgrades for their chassis.


Cautions

Thermaltake recommends the following steps to be taken before using the Pacific series radiators and water blocks

  • To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.
  • Do not use tap water or distilled water as your coolant, it may harm your loop and reduce performance.
  • It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while protecting the entire liquid loop from corrosion.
  • Before storing your water cooling components, please clean, rinse and dry. This will ensure a longer lifespan for your components.

Thermaltake recommends the following steps to be taken after completing your water loop setup

  • It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.
  • Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
  • DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately
  • Fill the reservoir to the top as it will prevent air from going into the pump
  • If necessary tilt the system slightly from side to side to bleed the air out of the loop.
  • Place some paper towels under fittings and joining points to test for leaks.
  • Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop.

Cautions

Thermaltake recommends the following steps to be taken before using the Pacific series radiators and water blocks:

  • To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.
  • Do not use tap water or distilled water as your coolant; it may harm your loop and reduce performance.
  • It is strongly recommended to use market-proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while protecting the entire liquid loop from corrosion.
  • Before storing your water cooling components, please clean, rinse, and dry them to ensure a longer lifespan for your components.

Thermaltake recommends the following steps to be taken after completing your water loop setup:

  • It is strongly recommended to use market-proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing corrosion in the entire cooling system – copper, brass, nickel, aluminum, and steel.
  • Fill the reservoir with coolant and cycle the power on and off several times while the pump pushes the coolant into the loop.
  • DO NOT let the pump run dry; turn off the power immediately if there is no liquid entering the pump.
  • Fill the reservoir to the top to prevent air from entering the pump.
  • If necessary, tilt the system slightly from side to side to bleed air out of the loop.
  • Place some paper towels under fittings and joining points to check for leaks.
  • Run the loop with the fill port open for about 24 hours to completely bleed air out of the loop.
  • Before starting, flush your system correctly to prevent any coolant or unwanted particles from sticking to your tubes, radiators, and other cooling components.
  • Note that coolant might fade over time.
More Information
P/N CL-W018-OS00TR-A
Material PVC
Inside Diameter 3/8”(9.5 mm)
Outside Diameter 5/8”(16 mm)
Color Transparent